LCDInfo.com

http://www.lcdinfo.com
It is currently Mon Oct 14, 2024 12:55

All times are UTC + 2 hours




Post new topic Reply to topic  [ 2 posts ] 
Author Message
PostPosted: Wed Oct 26, 2011 13:18 
Offline

Joined: Wed Oct 26, 2011 10:50
Posts: 2
Dont know if you guys can help but here goes...

I have 2 LC79430 based LCD's - yes from ebay! - here
http://www.ebay.co.uk/itm/300549241743? ... 1439.l2649

They are new LC79430 and LC79401 based. Model EDT EW50107FLYU 320x240
Pinout is as follows:
1 vo (interestingly, pin 2 and 3 dont adjust contrast with a pot or with -18v applied to vee and the pot connected)
2 vee
3 D3 to 79401
4 D2 to 79401
5 D1 to 79401
6 D0 to 79401
7 gnd
8 +5
9 CL2 to 79401
10 CL1 to 79430
11 FLM (DIOB0)
12 LED K
13 LED A
14 NU
Looks like 'm' is generated on board
I am using an atmega 88 so I can change the timing parameters of the timings.
My program works and LCDstudio works with another 320x240 LCD I have but with on board SED.
However, both progs give me a display on the new LCDs with a bought external board with the sed on it but it is as if the framing is too fast on it. I can see the x clocked data displayed in the correct x column but it is all down the screen (as if vertical hold is lost).

I have tried various initialisations in my program (lcdhype and lcdstudio wont allow display timing changes )

The current settings I use to init the sed are as follows (I am changing command &H40 P4, P5, P6 and P7 when I try setting up the display):
Call Lcd_send_cmd(&H40)
Call Lcd_send_data(&H30)
Call Lcd_send_data(&H87)
Call Lcd_send_data(&H07)
Call Lcd_send_data(&H27)
Call Lcd_send_data(&H55)
Call Lcd_send_data(&Hef)
Call Lcd_send_data(&H28)
Call Lcd_send_data(&H00)
Call Lcd_send_cmd(&H44)
Call Lcd_send_data(&H00)
Call Lcd_send_data(&H00)
Call Lcd_send_data(&Hf0)
Call Lcd_send_data(&Hb0)
Call Lcd_send_data(&H04)
Call Lcd_send_data(&Hf0)
Call Lcd_send_cmd(&H4c)
Call Lcd_send_cmd(&H5a)
Call Lcd_send_data(&H00)
Call Lcd_send_cmd(&H5b)
Call Lcd_send_data(&H01)
Call Lcd_send_cmd(&H59)
Call Lcd_send_data(&H10)
Call Lcd_send_cmd(&H5d)
Call Lcd_send_data(&H07)
Call Lcd_send_data(&H87)
Call Lcd_send_data(&H4c)
Call Lcd_send_cmd(&H46)
Call Lcd_send_data(&H00)
Call Lcd_send_data(&H00)
Call Lcd_send_cmd(&H42)

Sorry this is long winded, I know the sed can work with these chips from seeing other datasheets but I dont know what I am doing wrong....

Any help / pointersd appreciated.


Top
 Profile  
 
PostPosted: Thu Oct 27, 2011 9:31 
Offline

Joined: Wed Oct 26, 2011 10:50
Posts: 2
All Sorted! I had FLM connected to WF instead of YD and didnt realise I needed a -ve voltage on VEE - 3 x 9volt batteries proved that worked ok!

dicky


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 2 posts ] 

All times are UTC + 2 hours


Who is online

Users browsing this forum: No registered users and 32 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group