LCDInfo.com

http://www.lcdinfo.com
It is currently Sun Oct 06, 2024 15:22

All times are UTC + 2 hours




Post new topic Reply to topic  [ 11 posts ] 
Author Message
PostPosted: Fri Jan 17, 2003 1:20 
Offline

Joined: Thu Jan 16, 2003 12:56
Posts: 9
Hello
Do you know the NEC02070AA DISPLAY?


Top
 Profile  
 
 Post subject:
PostPosted: Fri Jan 17, 2003 21:32 
Offline

Joined: Sun May 05, 2002 22:05
Posts: 2063
Location: Lappeenranta, Finland
I don't know that display and a quick google search didn't reveal anything, sorry.

Maybe someone else here would know ?


Top
 Profile  
 
 Post subject:
PostPosted: Sun Jan 19, 2003 11:14 
Offline

Joined: Sun Dec 01, 2002 21:30
Posts: 24
I dont know about that lcd, but if you know what controller chip there is. You can try hollowing link's.
http://www.apollodisplays.com/manuals.php
http://www.eio.com/public/lcd/subject.html#2822


Top
 Profile  
 
 Post subject: datasheet lcd
PostPosted: Tue Jan 21, 2003 17:36 
Offline

Joined: Thu Jan 16, 2003 12:56
Posts: 9
Thanks,but my controller is a JRC CHIP...I don't know if it is compatible with ks0108 or t6936c controller or other.


Do ks0108 has memory for chr pattern ?
Thanks


Top
 Profile  
 
 Post subject: Re: datasheet lcd
PostPosted: Tue Jan 21, 2003 21:02 
Offline

Joined: Sun May 05, 2002 22:05
Posts: 2063
Location: Lappeenranta, Finland
AcidBit wrote:
Do ks0108 has memory for chr pattern ?

Do you mean if KS0108 has character generator ? It doesn't so you have to make your own font routines to draw text.


Top
 Profile  
 
 Post subject: lcd datasheet
PostPosted: Wed Jan 22, 2003 12:07 
Offline

Joined: Thu Jan 16, 2003 12:56
Posts: 9
Hello
it's OK..

I found this code in C language (CCS COMPILER ) for ks0108 128x64 lcd. it is free.
I posted it for newbie , it could somebody to help. I use it.
Do you know it ?


Code for PIC16f84-4/p
CCS COMPILER C

#include <16F84.H>
#use delay (clock=4000000)
#use fast_io(A)
#use fast_io(B)
#fuses nowdt,xt


struct ballstruct {
int1 xvect;
int1 yvect;
int8 xloc;
int8 yloc;
int8 oldx;
int8 oldy;
int8 oldx1;
int8 oldy1;
} *currball,ball[3] = {3,23,70,23,7 0,23,70,
2,28,40,28,40,28,40,
1,50,30,50,30,50,30};

char CONST msg1[4] = {0xc0,0x40,0xb8,0x3f};
int8 mult;

void write(char c) {
output_b(c); //Put character on PORTB
output_high(PIN_A3); //Pulse LCD Enable line
delay_cycles(1);
output_low(PIN_A3);
}

void setxy(int8 x,int8 y) { //x=vertical point (0-63) & y=horizontal point (0-127)
if(bit_test(y,6)) { //if y>63, then switch to controller on right side
output_high(PIN_A0);
output_low(PIN_A1);
}
else { //else use left side controller
output_low(PIN_A0);
output_high(PIN_A1);
}
output_low(PIN_A4); //Switch to Instruction mode
write(0xB8 | (x/8)); //Set memory bank to (x / 8)
write(0x40 | (y&0x3F)); //Set column to (y & 0x3F)
output_high(PIN_A4); //Switch to Data mode (Don't forget the pullup resistor!)
}

#int_rtcc
clock_isr() {
int8 data,oldx,oldy,x;

for(x=0;x<3;x++) { //Process all 3 balls
currball=&ball[x]; //Grab pointer to current ball

if((currball->xloc==0) && (currball->xvect==0)) //Edge detection on x-axis
currball->xvect = 1;
else if((currball->xloc==62) && (currball->xvect==1))
currball->xvect = 0;

if((currball->yloc==0) && (currball->yvect==0)) //Edge detection on y-axis
currball->yvect = 1;
else if((currball->yloc==126) && (currball->yvect==1))
currball->yvect = 0;

if(currball->xvect==0) //A value of 0 in vector will subtract 1 from the x-axis position
currball->xloc--;
else //A value of 1 in vector will add 1 to the x-axis position
currball->xloc++;

if(currball->yvect==0) //ditto
currball->yloc--;
else
currball->yloc++;

if(mult==2) { //Only update the screen every 3 interrupts
oldx=currball->xloc; //Save old position so it can be erased later
oldy=currball->yloc;

setxy(currball->oldx1,currball->oldy1); //Erase really old ball
write(0); // (2 pictures of each ball are on the
setxy(currball->oldx1,currball->oldy1+1); // screen at one time to minimize fading)
write(0);
setxy(currball->oldx1+1,currball->oldy1);
write(0);
setxy(currball->oldx1+1,currball->oldy1+1);
write(0);

currball->oldx1 = currball->oldx; //Move old position to really old position
currball->oldy1 = currball->oldy;

data=0;
bit_set(data,(currball->xloc % 8 )); //Draw new ball
if((currball->xloc % 8 )<7) { // This is a brute-force method, but it works
bit_set(data,(currball->xloc % 8 )+1);
setxy(currball->xloc,currball->yloc);
write(data);
setxy(currball->xloc,currball->yloc+1);
write(data);
}
else {
setxy(currball->xloc,currball->yloc);
write(data);
setxy(currball->xloc,currball->yloc+1);
write(data);
setxy(currball->xloc+1,currball->yloc);
write(1);
setxy(currball->xloc+1,currball->yloc+1);
write(1);
}
currball->oldx = oldx; //Move current position to old position
currball->oldy = oldy;
}
}
if(mult==2) { //If screen is updated, reset counter
mult=0;
}
else { //Otherwise increment
mult++;
}
}

void init() { //Initialize LCD
int8 x,y;

output_a(0); //Setup everything as outputs
output_b(0);
set_tris_a(0);
set_tris_b(0);

output_high(PIN_A0); //CS1 - high
output_low(PIN_A1); //CS2 - low
output_low(PIN_A4); //Instruction mode
for(x=0;x<4;x++) { //Send init chars
write(msg1[x]);
}

output_low(PIN_A0); //ditto, but for other controller
output_high(PIN_A1);
output_low(PIN_A4);
for(x=0;x<4;x++) {
write(msg1[x]);
}

output_high(PIN_A4); //My LCD starts up with all ram locations = 0xFF
output_high(PIN_A0); //This clears the ram
output_low(PIN_A1);
for(x=0;x<8;x++) {
for(y=0;y<64;y++) {
output_low(PIN_A4);
delay_cycles(1);
write(0xB8 | x);
write(0x40 | y);
output_high(PIN_A4);
delay_cycles(1);
write(0);
}
}
output_low(PIN_A0); //Clear other side
output_high(PIN_A1);
for(x=0;x<8;x++) {
for(y=0;y<64;y++) {
output_low(PIN_A4);
delay_cycles(1);
write(0xB8 | x);
write(0x40 | y);
output_high(PIN_A4);
delay_cycles(1);
write(0);
}
}
}

void main() {
int8 x;

init(); //Initialize LCD


setup_counters(RTCC_INTERNAL,RTCC_DIV_64); //Setup interrupts

enable_interrupts(INT_RTCC); //Start Interrupts
enable_interrupts(GLOBAL);



while(1); //Twiddle thumbs forever...
//Probably user input code will go here




}


note:
when I use write function for example:

setxy(0,0);
write (1) ; b'0000001'

The PIC 'light on' two pixel and not one. I dont't know why.

lcd screen
____________________________________________
|. pixel(0,0) pixel(0,64) . (why?)
|
|
|


Top
 Profile  
 
 Post subject:
PostPosted: Wed Jan 22, 2003 21:12 
Offline

Joined: Sun May 05, 2002 22:05
Posts: 2063
Location: Lappeenranta, Finland
Thanks for posting that code, I'm sure someone will find it useful. Maybe I could take advantage of it also.

You probably know that 128x64 KS0108 displays are made of two 64x64 controllers. It seems that when you write something to one controller the commands go to the second also. CS pins are used to tell the controllers which one is enabled at a time. I didn't check the code very carefully but I think it should be ok unless you have made some changes to it. So maybe there's some problem with your wiring of CS pins. Did you find any information about the hardware connection used with this code ?


Top
 Profile  
 
 Post subject: lcd datasheet
PostPosted: Thu Jan 23, 2003 0:02 
Offline

Joined: Thu Jan 16, 2003 12:56
Posts: 9
The code is written by Barry Michels <bmichels@EPIX.NET>

RW pin is grounded

port A0 CS1
port A1 CS2
port A3 Enable line
port A4 Register Select
port B data lines

note:
I resolved my problem a wire was wrong..

I would to use a touch screen togheter graphic lcd, Do you know touch screen?


Top
 Profile  
 
 Post subject:
PostPosted: Thu Jan 23, 2003 21:06 
Offline

Joined: Sun May 05, 2002 22:05
Posts: 2063
Location: Lappeenranta, Finland
Good to hear that your problem is now solved.

I don't have any experience with touch screens but they are an interesting subject that I'd like to explore sometime.


Top
 Profile  
 
 Post subject: nec02070aa
PostPosted: Mon May 12, 2003 10:58 
Offline

Joined: Mon May 12, 2003 10:51
Posts: 1
Location: Cluj, Romania
Hi!
Have you found the specs for the display?
I've bought one such thing myself and the supplier told me they can give me the specs, if I can't find them.
I didn't think i'm not going to find the stuff on the net, so i said no thanks.
But I can go back there and ask for the disk. If you still need the file, I can send it to you.


Top
 Profile  
 
PostPosted: Wed Jan 11, 2012 16:17 
Offline

Joined: Sat Jan 31, 2009 12:08
Posts: 1
I have one LCD display , too. Please let me know the pin configuration, please!
Thank you!


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 11 posts ] 

All times are UTC + 2 hours


Who is online

Users browsing this forum: No registered users and 9 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group