LCDInfo.com

http://www.lcdinfo.com
It is currently Mon Nov 25, 2024 10:40

View unanswered posts | View active topics


Board index » LCDInfo 0.6-> » Drivers

All times are UTC + 2 hours




Post new topic Reply to topic  Page 6 of 12
  [ 174 posts ]  Go to page Previous  1 ... 3, 4, 5, 6, 7, 8, 9 ... 12  Next
  Print view Previous topic | Next topic 
Author Message
voodoo
 Post subject:
PostPosted: Sat Apr 17, 2004 19:04 
Offline

Joined: Wed Apr 07, 2004 21:06
Posts: 2
Location: Portugal / Coimbra
in 7110 ?? what controler use :s
Top
 Profile  
 
Henri
 Post subject:
PostPosted: Mon Apr 19, 2004 13:01 
Offline

Joined: Sun May 05, 2002 22:05
Posts: 2063
Location: Lappeenranta, Finland
A guess on the 7110 controller could be SED1565. Sorry, I don't have more information on this.

I checked the datasheet for OM6208 and it includes I2C interface too so I don't think this is the correct controller.
But 6310 could use the same controller that is used in 3410. I don't know the controller for this either but I found one controller datasheet from Philips site that matched with what I know about the 3410 controller. Sorry, can't remember which controller it was but if you look into the datasheets and find the one for this size and with SPI interface only then you have it.
Top
 Profile  
 
mojiro
 Post subject:
PostPosted: Tue Apr 20, 2004 10:22 
Offline

Joined: Mon Apr 19, 2004 11:42
Posts: 8
Location: Greece/Korydallos
i have 5110 screen and i have problem with
the connector !!! i know the pins and their
connection but it is to difficult to make a
connector !!!! in this lcd the connector has
9 pin on a silicon like pad.

i have thought many ways but the best was to
take a utp female connector and modifiacate
it so to fit the screen.

do you have any idea ? what you did in that
case?

_________________
YOU DONT NEED EYES TO SEE
YOU NEED VISION (OR A NICE LCD:)
Top
 Profile  
 
sadashiv_sm
 Post subject:
PostPosted: Thu Apr 22, 2004 12:41 
Offline

Joined: Sat Mar 27, 2004 10:38
Posts: 14
Location: India

hi henri....!!!
thanx for your reply....!!!!!

i am not getting which controller is in 6310 and 6210...
i searched a lot on the philips site....but dint got any results...
is it possible for u to remember the number of the controller...

thanx in advance....

thanks........!!!!

_________________
With Warm Regards From....!!!

Sada...!!!!
Top
 Profile  
 
Henri
 Post subject:
PostPosted: Sat Apr 24, 2004 9:49 
Offline

Joined: Sun May 05, 2002 22:05
Posts: 2063
Location: Lappeenranta, Finland
I can check the pdfs some day when I'm on a faster connection...
Top
 Profile  
 
Spike
 Post subject:
PostPosted: Sat Apr 24, 2004 12:24 
Offline

Joined: Sat Apr 24, 2004 12:21
Posts: 4
jetage wrote:
henri:
got my display working..
http://hem.bredband.net/b113013/dator/n ... schema.jpg

thanks anyway..

yes my voltage is a bit strange on my pin7.. but who cares?


-------------------
ADMIN EDIT:
jetage reported me that his display died using this schematic. So others might not want to try this one.


Whats the thing between LTP7, LTP25 & GND / VOUT?
Maybe I can post my result here, I have a nokia 5110 display..
anyone....help?
Top
 Profile  
 
Henri
 Post subject:
PostPosted: Sun Apr 25, 2004 18:03 
Offline

Joined: Sun May 05, 2002 22:05
Posts: 2063
Location: Lappeenranta, Finland
Spike wrote:
Whats the thing between LTP7, LTP25 & GND / VOUT?

It's a 3.3v voltage regulator.
Top
 Profile  
 
Spike
 Post subject:
PostPosted: Mon Apr 26, 2004 21:21 
Offline

Joined: Sat Apr 24, 2004 12:21
Posts: 4
Can I leave that thing behind if I use an external power suppy, or do I really need him?
Top
 Profile  
 
nokie2
PostPosted: Mon Apr 26, 2004 23:09 
Offline

Joined: Mon Apr 26, 2004 23:04
Posts: 1
hi henry


i have an old 486 dx2 66 mhz :lol: and an unused nokia 8210 , guide me so i can get an interface between them and be able to display information on nokia´s lcd using this computer?
Top
 Profile  
 
Henri
 Post subject:
PostPosted: Tue Apr 27, 2004 10:00 
Offline

Joined: Sun May 05, 2002 22:05
Posts: 2063
Location: Lappeenranta, Finland
Spike wrote:
Can I leave that thing behind if I use an external power suppy, or do I really need him?

You can leave that but in that case you lose the possibility of the software to control the power supply of the display. In the controller datasheet it's said that the display should be resetted immediately after applying power to not to damage it.

nokie2 wrote:
hi henry

i have an old 486 dx2 66 mhz and an unused nokia 8210 , guide me so i can get an interface between them and be able to display information on nokia´s lcd using this computer?

It shouldn't matter what x86 system you have as long as you can run the software given here. All instructions given here should apply.
Top
 Profile  
 
Spike
 Post subject:
PostPosted: Tue Apr 27, 2004 14:13 
Offline

Joined: Sat Apr 24, 2004 12:21
Posts: 4
Can any one make a scheme of 9pins nokia 5110display, with external power supply? :) I would love it!

Fixed it....busy with 9th pin... but il lpost it inhere..sometime :) :roll: :P :wink:
Top
 Profile  
 
Henri
 Post subject:
PostPosted: Thu Apr 29, 2004 15:40 
Offline

Joined: Sun May 05, 2002 22:05
Posts: 2063
Location: Lappeenranta, Finland
Are you still wondering about the extra pin ?

Earlier in this thread:
Henri wrote:
The connection is same as for the 8 pin display except you need to connect the Osc pin to Vdd. According to PCD8544 datasheet this enables the on-chip oscillator.
Top
 Profile  
 
Spike
 Post subject:
PostPosted: Fri Apr 30, 2004 13:37 
Offline

Joined: Sat Apr 24, 2004 12:21
Posts: 4
Vdd = 5volts right? Also extern? Or just leave it behind, it will work without?
Top
 Profile  
 
Henri
 Post subject:
PostPosted: Sat May 01, 2004 16:49 
Offline

Joined: Sun May 05, 2002 22:05
Posts: 2063
Location: Lappeenranta, Finland
Vdd is the operating voltage of the PCD8544 chip. 3.3v in my schematic.
Top
 Profile  
 
DonFranczesko
 Post subject:
PostPosted: Sat May 15, 2004 12:52 
Offline

Joined: Sat May 15, 2004 12:47
Posts: 7
Hi!

I want to make Nokia 3310 LCD working, but now I don`t know which scheme is good :) First, I rather not use DarkElf scheme, becouse those parts are hard to get for me (especialy 74xx)... second, Jetage scheme gives too high voltage, so its not good for LCD...

Is there an alternative for this 74xx part?
Which scheme is good?
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 6 of 12
  [ 174 posts ]  Go to page Previous  1 ... 3, 4, 5, 6, 7, 8, 9 ... 12  Next

Board index » LCDInfo 0.6-> » Drivers

All times are UTC + 2 hours


Who is online

Users browsing this forum: No registered users and 0 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group