LCDInfo.com

i Found my old 5210 any one has any idea where i could find specks for this display?
i used google but couldt find anything use full

and i found these from phone

DF7_06
9854572
somethink like "A" and "S02" and smol "27b" (AS0227b)
R394V-0

Any one any help??

I've read, that the display is the same with other nokia's, but the result is reflected.

_________________
gsmaster

I've been looking for informations about nokia displays for a long time, and What I found is that all uses the same controller (PCD8544) and the PN is LPH7366 for some Nokia display. There are lots of projects with them.
http://sandiding.tripod.com/Bertys.html
http://rifer.narod.ru/usblcd.html

according to the data sheet your display seems to be a LPH7779/7677 compliant one (8 pins)
@dantasad_28: lph7366 has 9 pins ...

but all of these are driven by the same controller (pcd8544 or compliant)

/mrwastl

DAM im soooo confused
im not wery fimiliar whit these ports and pins,
and i hawe so poor english

is LPT = 25pin printer port?

where did you read LPT?

LPH != LPT

LPH7779, ... are model names. if you would have read some of the existing projects you would have read about those different model names.

some urls:

(dantasasd_28 already posted a link to Bertys pages):
http://sandiding.tripod.com/lcd.html

my own project: http://serdisplib.sourceforge.net
(use http://serdisplib.sourceforge.net/ser/pcd8544.html for your display)

and many others (some are listed in the page above)

/mrwastl

http://sandiding.tripod.com/lcd.html <-- end of that pake says

"Lpt port connectivity"

And link goes to....
HERE ----> http://serdisplib.sourceforge.net/ser/pcd8544.html

Can i use that wiring??
if not, any of u hawe direct wiring quide and now i read those links

NOKIA 5210 pinout tested



inverted display can be seen in a digital clock application.

Perhaps Henry could add a modified driver for these displays, so they can be used with LCDinfo.

_________________
gsmaster

DAM i all ready left that project and ordered 2x16 lcd .
http://www.bebek.fi/kauppa/tuotekuvat_u ... 0a00d7.jpg

and i would realy like to see those picks but they wont load up.
edit. server was down i ques.

i thinked that i could use 2 LCD, so i started to selder first but noticed that i cant do it

So pin out goes like?

RES => LPT pin 4
Vout => LPT pin ?
GND => LPT pin ?
CS => LPT pin ?
D/C => LPT pin 6
SDA => LPT pin 3
SCL => LPT pin 2
VDD => LPT pin ?

i all ready soldered those so i hope that is ok.

With LCDInfo you can use whatever pins from the LPT datalines (2-9) and then set the same pins in LCDInfo.

You also need to connect a small capacitor (ceramic or polyester) between the VOUT & CS pins and the CS pin also to GND.

For example:

RES => LPT 4
GND => LPT 18-25
D/C => LPT 6
SDA => LPT 3
SCL => LPT 2
VDD => LPT 9 (to be safe you could put a diode between VDD & LPT pin 9, the stripe facing away from the LPT port.)

VOUT => capacitor => CS
CS => GND

i just soldered alll those and nothing ? hawe i some think to remember?

Propably doesn't work because the PCD8544-driver in LCDInfo is for a different model. Unless someone writes a new one.